ブログ について Is a 1.54-Inch High Brightness 1000nits TFT LCD the Right Trade-Off for Your Square-Format HMI?

Square displays are a distinct design category. A 1.54-inch high brightness 1000nits TFT LCD with 240 × 240 resolution offers a centered, symmetric canvas that suits gauges, dials, wearable pods, and compact instrument faces. But square format also means square trade-offs: the same pixel count in both axes, an SPI interface that limits refresh rate, a 9.6 V backlight string that needs a boost converter, and a 900–1100 cd/m² brightness range that is impressive on a datasheet but demanding in a sealed enclosure.

The SF-TC154B-8945B-N from Saef Technology Limited is a useful reference for evaluating those trade-offs. It is a 1.54-inch square IPS TFT with 240 × 240 resolution, ST7789V controller, SPI interface, and a white-LED backlight rated at 9.6 V / 20 mA with 900–1100 cd/m² output. This article is built as a decision matrix: six design dimensions, each with a quantified comparison table, followed by the engineering conclusion. The full pin definitions, timing, and optical specifications are in the SF-TC154B-8945B-N_SPECIFICATION.pdf. Place this link in the decision-matrix introduction, with the anchor text above.

Key technical specifications

Decision 1: Square 240 × 240 vs rectangular 240 × 320

Conclusion: A 1.54-inch high brightness 1000nits TFT LCD with square format is the better fit for radial gauges, centered icons, and wearable pods. It also reduces frame buffer and SPI transfer time by about 25% versus a 240 × 320 panel. If the UI is primarily text-heavy, a rectangular panel remains more efficient. For square-format HMI, the square panel wins on layout and memory.

Decision 2: SPI bandwidth vs UI refresh expectation

The datasheet’s SPI write cycle is 66 ns minimum, but the host’s achievable clock is the real limit.

At 10 MHz, a 1.54-inch high brightness 1000nits TFT LCD can sustain about 11 full frames per second. That is enough for a gauge needle and a numeric readout, not for scrolling text. The firmware should use partial updates via the ST7789V address-window commands. Design the UI around changed regions, not full-screen redraws. If the product needs 30+ fps full-frame, the SPI interface is the bottleneck, not the display.

Decision 3: 9.6 V backlight string vs 5 V rail

The backlight needs a boost converter with a duty cycle near 52% at minimum input. A 470 µH inductor and a small Schottky diode are sufficient. A series resistor from 5 V cannot drive a 9.6 V string. The boost converter should be constant-current, with PWM dimming and an enable pin that is sequenced after the logic rail. On a 1.54-inch high brightness 1000nits TFT LCD, the backlight is a small but non-trivial power supply design.

Decision 4: Thermal rise in a sealed wearable pod

At 40°C ambient in a sealed pod, the LED junction is estimated near 59°C. The datasheet’s lifetime curve is specified at 25°C; running at 59°C will shorten the LED life. The practical fixes are a thermal pad from the LED bar to the enclosure, a brightness derating policy above 35°C ambient, or both. A 1.54-inch high brightness 1000nits TFT LCD is small, but 192 mW in a sealed pod is not negligible.

Decision 5: Resistive touch vs capacitive touch on a square 1.54-inch panel

At 40°C ambient in a sealed pod, the LED junction is estimated near 59°C. The datasheet’s lifetime curve is specified at 25°C; running at 59°C will shorten the LED life. The practical fixes are a thermal pad from the LED bar to the enclosure, a brightness derating policy above 35°C ambient, or both. A 1.54-inch high brightness 1000nits TFT LCD is small, but 192 mW in a sealed pod is not negligible.

Decision 5: Resistive touch vs capacitive touch on a square 1.54-inch panel

The module’s IOVCC accepts 1.8 V or 2.8 V, while VCC is 2.8 V. A 3.3 V host should either use a level shifter on the SPI lines or verify that the module’s input thresholds tolerate 3.3 V. The datasheet’s VIH is 0.8 × VDD, and VIL is 0.2 × VDD; 3.3 V logic may exceed the absolute maximum if VDD is 2.8 V. Check the level matching before connecting a 3.3 V MCU. On a 1.54-inch high brightness 1000nits TFT LCD, the interface voltage is a small detail that can damage the controller if ignored.

Final engineering note

A 1.54-inch high brightness 1000nits TFT LCD is a square-format display with a square-format set of trade-offs. The 240 × 240 resolution reduces frame buffer size and SPI transfer time versus a rectangular panel, the 9.6 V backlight requires a boost converter, the 192 mW backlight needs a thermal path in a sealed pod, and the SPI interface sets a practical full-frame ceiling around 11–22 fps. The touch stack and the I/O level matching are the two decisions most often deferred and most expensive to fix after the enclosure is frozen.

For a design review, bring the decision matrix and the enclosure thermal data to the engineering team at Saef Technology Limited. The team can confirm the module configuration, discuss the custom CTP or RTP options, and review the SPI level matching before the carrier board is finalized.